Topic: Knock sensors 2002

[Alaska_AV]

I was looking fwd to a custom tune but my AV had other ideas
The rear knock sensor decided to die after 170K. I decided to do an upgrade also. I knew I still had the old intake gaskets that are prone to going bu bie. I set out on EBAY.

I won new Green gaskets for $30 or so shipped, Better than $80+
ordered 2 knock sensors for $50 from global
Chevy says to build a dam of silicone around the rubber plug to keep water out

I read 100 posts on-line about what was gonna happen...lol I'm used to the old intakes and this wasn't so bad. I had 1/4 inch of gunk under the intake. I plugged, scraped, scrubbed and vacuumed for an hour. When I was snapping the gaskets on the intake I looked at my injectors........... Every 2 mo or so I have tried adding injector cleaner, STP and normal gas station CRAP. What a waist.   My Injectors were nasty! Half clogged and did I say nasty. my dealer wants $95 apiece $795 all 8......OMG ..... Did I say, I will NEVER pay them that!   So I set them in cleaner, tip only. and set out to get rid of what gunk I could. That stuff was tough.

Well the Av now runs Awesome! New Injectors are still coming , from some were.  The Dealer still wants $130 to clean them, Guess thats going toward new to me, ones...lol

[bluedevil]

Thats great.


How do you clean the injectors?  You dip 'em and let them soak?   or?

[oHIobellboy]

 


Just had to do that. LOL


Sounds like you did your own custome tune by cleaning everything up. How much total time did you have in this project?

[Alaska_AV]

It was a casual Sunday afternoon/evening. I took a 2 hour break to decide what to do about the injectors. While they soaked.


I didn't really clean the injectors, you need pressure!, I just removed the baked on crap on the ends. I think I have gained 20 miles out of the bottom half tank of gas, since doing this. Very good considering I'm romping on it left and right. Hell my leg is cramping up from holding it of the gas while cruising. I've been fighting the 13 mpg it's been getting for the last 2 years. Every thing I did would put it up to 14+ then fall off. I hope this takes!

Anyway I soaked the ends in carb cleaner. took a wire tooth brush to the gunk. Then rinsed with spray cleaner. I notice the outer ring on the bottom freely spun on the cleanest one. so I dipped the ends in air tool oil and spun every one of them then hit with the spray cleaner again. the gunk flew!!!!! At this point I didn't care if they lived long or not..... Hit the O-rings with the oil and put them in


I took no pics. I was finally embarrassed by how dirty it was.......
 

[oHIobellboy]

Hey man,no need to be embarrassed, you had no clue what it looked like in there. Like you stated, you tried running cleaner in it pretty regular.

[WB]

OK...I'm dumb.....How do you get them out??   

I wanna see mine!!!       

WB

[oHIobellboy]

OK...I'm dumb.....How do you get them out??   

I wanna see mine!!!      

WB

I hope you're talking about the injectors.

[WB]

I hope you're talking about the injectors.

Sure you could call them that....   

YES, the injectors need cleaned!!   

Do you need a special tool or is it easy to do??

[oHIobellboy]

Sure you could call them that....  

YES, the injectors need cleaned!!  

Do you need a special tool or is it easy to do??

I think it's time we start pressuring a certain person to have a mod party at the "Mod Garage". Now where's CDW when you need him.

[WB]

I think it's time we start pressuring a certain person to have a mod party at the "Mod Garage". Now where's CDW when you need him.

I scared him so bad he's leaving the state!!   

No one has the stomache to hang with the buffalo's owner!!!