Author Topic: Decal installation instructions (Read 3603 times)

bluedevil · « **on:** October 22, 2006, 03:29:57 PM »

• Application:

Lay the decal along with the transfer tape, and backing flat against the surface that you wish to apply it to. Once the decal is in the position you desire use a piece of masking tape on each end to hold it in place. Now, leaving one edge of the decal taped to the surface, remove the other edge and fold the decal away from the surface, so that the backing is facing you. Carefully remove the backing making sure the decal (and all of it's parts) is firmly attached to the transfer tape. Once the backing is removed, carefully fold the decal back onto the surface in a rolling motion. The transfer tape will keep the decal together, and aligned with itself. Once the entire decal has contacted the surface, with the transfer tape still attached, rub the decal onto the surface with a squeegee, your fingers or a credit card to remove any bubbles and to insure good adhesion all over entire decal. The transfer tape allows you to firmly rub the decal without damaging it.

When the decal has been completely applied to the surface, gently peel away the transfer tape. The decal will adhere to the surface much more aggressively than the transfer tape and the tape should peel away freely leaving no residue.

If there are bubbles present under the decal that cannot be removed by working them to the edge of the decal, a small pin or needle can be used to puncture the bubble and remove the air. A small pin hole will not be seen after the air bubble has been worked out.

The application of vinyl decals is not terribly difficult but it is best to work carefully and slowly. Don't try to rush the process or you could mess it up and ruin your decal. Once applied the decals cannot be repositioned, so take your time. It is also critical that the decals be applied at the correct temperature (between 60 & 80 degrees Fahrenheit). If the decal is applied at temperatures below 60 degrees they may not adhere properly. If the decal is applied at temperatures above 80 degrees air bubbles may form under the vinyl after it's applied.

Flint 4X4 · « **Reply #1 on:** October 22, 2006, 04:30:55 PM »

Can I add some obvious instructions ? I'm going to anyway

If decal is to be added to backglass, take the window out and put it on a table.

If you want to put it across the top of your windshield it's real easy if you have a sunroof.

bluedevil · « **Reply #2 on:** October 22, 2006, 04:52:56 PM »

I used the lower defroster line as a reference when applying decal. Nice and straight :thumb:

Flint 4X4 · « **Reply #3 on:** October 22, 2006, 05:15:02 PM »

Quote from: BlueDevil on October 22, 2006, 04:52:56 PM

I used the lower defroster line as a reference when applying decal. Nice and straight :thumb:

I missed the most obvious instruction for applying a decal, can you guess what it is ?

bluedevil · « **Reply #4 on:** October 22, 2006, 05:31:38 PM »

Quote from: Flint 4X4 on October 22, 2006, 05:15:02 PM

Quote from: BlueDevil on October 22, 2006, 04:52:56 PM
I used the lower defroster line as a reference when applying decal. Nice and straight :thumb:

I missed the most obvious instruction for applying a decal, can you guess what it is ?

Flint 4X4 · « **Reply #5 on:** October 22, 2006, 05:41:21 PM »

It's quite simple really,......

Visit BlueDevil or Flint4x4 and get them to do it for you

bluedevil · « **Reply #6 on:** October 22, 2006, 05:55:36 PM »

Right on! :thumb:

mEYEscndfvrtluv · « **Reply #7 on:** October 22, 2006, 06:45:48 PM »

i'll bring the JD! :thumb:

Flint 4X4 · « **Reply #8 on:** October 22, 2006, 06:49:48 PM »

Quote from: myscndfvrtride on October 22, 2006, 06:45:48 PM

i'll bring the JD! :thumb:

I still have my sample bottle from Southern Nights

bluedevil · « **Reply #9 on:** October 25, 2006, 09:51:42 PM »

Quote from: BlueDevil on October 22, 2006, 04:52:56 PM

I used the lower defroster line as a reference when applying decal. Nice and straight :thumb:

Jeff & Chris. Just in case you missed this post.

Do this when applying decal. It will come out nice and straight. (Use bottom defroster line). If you go any lower than that, decal will be behind the glass seal.

mEYEscndfvrtluv · « **Reply #10 on:** October 25, 2006, 10:11:25 PM »

thx BD! :thumb:

shawn1007 · « **Reply #11 on:** April 12, 2008, 09:56:27 AM »

as a former graphic installer... there is one trick of the trade that allows movement and total air removal....
tools needed: squirt bottle(mist), drivers license or credit card
get a squirt bottle, make a VERY mild soapy mix (DO NOT USE DAWN),
clean the surface
mist the surface with the soap mix
lay the graphic onto the surface, position as needed
Using the drivers license or credit card, gently "squeegy" the graphic from the center out.
let sit approx 5-10 minutes and then peel the temp backing off of the graphic and whalla!
If you find that you have a few bubbles, you can use a straight razor blade and make a tiny slice and rub out the bubble

boilers94 · « **Reply #12 on:** April 12, 2008, 11:42:35 AM »

Great tips, Shawn1007!!

shawn1007 · « **Reply #13 on:** April 12, 2008, 12:13:04 PM »

Boiler, where are you in ohio? I am from cincy... graduated Glen Este in '89

Flint 4X4 · « **Reply #14 on:** April 12, 2008, 01:11:10 PM »

Quote from: shawn1007 on April 12, 2008, 09:56:27 AM

If you find that you have a few bubbles, you can use a straight razor blade and make a tiny slice and rub out the bubble

I tried that on my waterbed

I've used Windex and a plastic squeegy from center out.
I had one tiny bubble on my Avalanche windshield decal, I popped it with a pin a rubbed it out.

shawn1007 · « **Reply #15 on:** April 12, 2008, 09:47:11 PM »

windex will eventually lead to the glue breaking down.... lets hope you didnt use too much!

Flint 4X4 · « **Reply #16 on:** April 14, 2008, 07:35:28 AM »

Quote from: shawn1007 on April 12, 2008, 09:47:11 PM

windex will eventually lead to the glue breaking down.... lets hope you didnt use too much!

Four years no problem in Michigan's ever changing weather, more chance I'd tear it with a window scaper.
Probably depends on type of glue/how much glue, how the glue was applied/type of vinyl etc.

TannerMac · « **Reply #17 on:** September 10, 2008, 02:56:05 PM »

Mission accomplished !!

bluedevil · « **Reply #18 on:** September 10, 2008, 03:45:49 PM »

Quote from: TannerMac on September 10, 2008, 02:56:05 PM

Mission accomplished !!

TannerMac · « **Reply #19 on:** September 10, 2008, 04:15:08 PM »

Not been around long enough to post pics yet... or so I was told.

bluedevil · « **Reply #20 on:** September 10, 2008, 04:37:59 PM »

Quote from: TannerMac on September 10, 2008, 04:15:08 PM

Not been around long enough to post pics yet... or so I was told.

What? Post away man!

TannerMac · « **Reply #21 on:** September 10, 2008, 05:00:29 PM »

Thanks... maybe that was over in the National Club where you have to be around for awhile before you can post.

Sorry for the confusion.

bluedevil · « **Reply #22 on:** September 10, 2008, 05:36:53 PM »

Quote from: TannerMac on September 10, 2008, 05:00:29 PM

Thanks... maybe that was over in the National Club where you have to be around for awhile before you can post.

Sorry for the confusion.

Wow! Excellent pic. Turned out great

Do you mind if i use your pic here? http://www.midwestavalancheclub.com/index.php?action=decals

...oh yeah.... the other site you need atleast 15 or 25 posts or so to upload pics,send messages and stuff like that.

TannerMac · « **Reply #23 on:** September 10, 2008, 06:27:37 PM »

BlueDevil,

I give you my permission, I'd be honored.

Thanks Again

P.S. don't forget about contacting me when you are coming up to Rochester MN.

bluedevil · « **Reply #24 on:** September 10, 2008, 06:31:52 PM »

Quote from: TannerMac on September 10, 2008, 06:27:37 PM

BlueDevil,

I give you my permission, I'd be honored.

Thanks Again

P.S. don't forget about contacting me when you are coming up to Rochester MN.

Thanx! Ive been meaning to replace that pic in the store but my camera stinks. ...... Sure thing bud,i think we have an appointment sometime this year.

boilers94 · « **Reply #25 on:** September 10, 2008, 07:02:10 PM »

Quote from: shawn1007 on April 12, 2008, 12:13:04 PM

Boiler, where are you in ohio? I am from cincy... graduated Glen Este in '89

shawn1007,

Sorry it took me so long to see this post! I'm from the Wilmington, OH, area which is about 40 miles north of Cincinnati.

oHIobellboy · « **Reply #26 on:** September 10, 2008, 07:09:40 PM »

Great job TannerMac

Now you need to get your camera out and snap a pix of an Avy in your rearview mirror.
Here's an example:

TannerMac · « **Reply #27 on:** September 11, 2008, 06:27:44 PM »

Quote from: oHIobellboy on September 10, 2008, 07:09:40 PM

Great job TannerMac Now you need to get your camera out and snap a pix of an Avy in your rearview mirror.
Here's an example:

I'll work on that over the weekend... Looks like it may take a try or two to get the best shot

Donnie1 · « **Reply #28 on:** September 11, 2008, 09:48:59 PM »

Or like this:

oHIobellboy · « **Reply #29 on:** September 11, 2008, 09:51:12 PM »

Kewl pix Donnie

Sunburst05 · « **Reply #30 on:** September 11, 2008, 09:52:32 PM »

Speaking of decals,,,,,,, Hey Mick I hope you don't mind me using the new 4" as my new avatar. If it is okay then I would like to use it also on TOS.

oHIobellboy · « **Reply #31 on:** September 11, 2008, 09:53:35 PM »

Quote from: Sunburst05 on September 11, 2008, 09:52:32 PM

Speaking of decals,,,,,,, Hey Mick I hope you don't mind me using the new 4" as my new avatar. If it is okay then I would like to use it also on TOS.

I don't think he'll mind a bit. I use a banner myself unless there's a gtg on the way.

Donnie1 · « **Reply #32 on:** September 11, 2008, 09:55:14 PM »

Quote from: oHIobellboy on September 11, 2008, 09:51:12 PM

Kewl pix Donnie

Thanks. That was MoAv headed to Fire and Ice with us this year. Mo and Paul stayed the night with us and then we rolled into Jeff's and surprised everybody. Kinda like someone else did a couple of weeks ago.

Sunburst05 · « **Reply #33 on:** September 11, 2008, 10:05:51 PM »

Quote from: oHIobellboy on September 11, 2008, 09:53:35 PM

I don't think he'll mind a bit. I use a banner myself unless there's a gtg on the way.

I'll take this as a okey dokey then.

bluedevil · « **Reply #34 on:** September 11, 2008, 10:10:02 PM »

Quote from: Sunburst05 on September 11, 2008, 10:05:51 PM

I'll take this as a okey dokey then.

oHIobellboy · « **Reply #35 on:** September 12, 2008, 04:55:30 AM »

I like the idea. BD, will you add that to the avatar in the Promote section?

bluedevil · « **Reply #36 on:** September 12, 2008, 06:27:02 AM »

Quote from: oHIobellboy on September 12, 2008, 04:55:30 AM

I like the idea. BD, will you add that to the avatar in the Promote section?

after work